Quick answer: multiply length × width × pour depth (all in inches) to get cubic inches, add 10% for waste, then multiply by 0.554 to get US fluid ounces. A 48 × 30 inch tabletop with a ⅛ inch flood coat needs about 110 fl oz, a little under a gallon, of mixed epoxy.
volume (cubic inches) = length × width × depth
For round pieces, use π × radius² × depth instead of length × width.
Then convert:
- cubic inches × 0.554 = US fluid ounces
- cubic inches × 16.39 = milliliters
- fluid ounces ÷ 128 = US gallons
Remember that this is the volume of mixed epoxy, resin and hardener together. A 1:1 kit gives you half from each bottle; a 2:1 kit gives you two thirds resin and one third hardener.
How much to add for waste
Some epoxy never makes it onto your project. It stays in mixing cups, drips off the edges and soaks into raw wood.
- 10% for sealed surfaces and small pieces in a mould
- 15% for raw or porous wood, live edges and flood coats that run over the sides
- 20% if it's your first pour or the surface is uneven
Worked examples
All of these include the waste allowance shown. They were calculated with the epoxy resin calculator, so you can change any measurement to match your project.
| Project |
Size and depth |
Waste |
Mixed epoxy |
Metric |
| 6 round coasters |
4 in diameter, ⅛ in deep |
10% |
5.7 fl oz |
170 ml |
| Serving tray |
18 × 12 in, ¼ in deep |
10% |
32.9 fl oz |
973 ml |
| Dining tabletop |
48 × 30 in, ⅛ in flood coat |
10% |
109.7 fl oz (0.86 gal) |
3.2 L |
| Bar top |
96 × 24 in, ⅛ in flood coat |
10% |
175.5 fl oz (1.37 gal) |
5.2 L |
| River table |
72 × 36 in slab, 1½ in deep, river is 30% of the area |
15% |
743 fl oz (5.8 gal) |
22 L |
Working through the tabletop
- Volume: 48 × 30 × 0.125 = 180 cubic inches
- Add 10%: 180 × 1.1 = 198 cubic inches
- Convert: 198 × 0.554 = 109.7 fl oz, or about 0.86 US gallons
- With a 1:1 kit, mix roughly 55 fl oz of resin with 55 fl oz of hardener
A 1-gallon kit (two half-gallon bottles, 128 fl oz total) covers this table with a little to spare.
Working through the river table
River tables are where estimates go wrong, because the river is only part of the slab. Measure the river itself, or estimate what share of the slab it covers.
- Full slab volume: 72 × 36 × 1.5 = 3,888 cubic inches
- River share: 30% of that = 1,166 cubic inches
- Add 15% for wood absorption and mould leaks: about 1,341 cubic inches
- Convert: about 743 fl oz, or 5.8 gallons
That's a deep pour, so you'd use a deep-pour casting epoxy, often poured in more than one layer depending on the product's maximum depth.
Buying tips
Buy kits by mixed volume. Kit sizes are usually stated as the combined volume of both parts. A "1 gallon kit" normally means half a gallon of each.
Round up, not down. Running out partway through a flood coat leaves a visible line. Leftover epoxy keeps for months if sealed, and you can use it on small projects.
Plan multiple coats separately. A seal coat on raw wood, then a flood coat, means two calculations. Seal coats are thin and use much less.
Check the depth limit. Tabletop epoxies are typically designed for layers around ⅛ inch. Pouring deeper can overheat and crack. Follow the maximum on your product.
Metric examples
Using 1 cm³ = 1 ml:
| Project |
Size and depth |
With 10% extra |
| Tabletop |
120 × 60 cm, 3 mm coat |
about 2,376 ml (2.4 L) |
| Round mould |
30 cm diameter, 1 cm deep |
about 778 ml |
For rectangles: length × width × depth in centimetres = millilitres. For circles: 3.1416 × radius × radius × depth.
A seal coat changes the total
Raw wood soaks up epoxy. A thin seal coat, often brushed on at about 1/16 inch, stops bubbles rising from the wood into your flood coat. For the 48 × 30 inch tabletop example, a seal coat at 1/16 inch adds roughly half the flood coat amount, about 55 fl oz with waste. Budget for it when you buy.
Edges and drips
If the flood coat runs over the edges, the edges take resin too. For a ¾ inch thick tabletop, the four edges of a 48 × 30 inch table add about 117 square inches of surface. Most of the run-off drips away, which is why flood coats need the waste allowance at the higher end, 15% or more.
Common mistakes
Measuring the wrong depth. ⅛ inch is 3 mm, not 1/8 of a centimetre. Mixing units is a common error.
Forgetting the second coat. Many tabletops get a seal coat and a flood coat. That's two purchases, not one.
Buying the exact amount. Kits are sold in fixed sizes, and running out partway through a pour leaves a visible line. Round up.
Mixing too much at once. A large batch in one cup heats up and shortens working time. For big areas, mix in manageable batches.
Quick checklist
- Measure length, width and depth in the same units.
- Calculate the volume, then add 10% to 15% for waste.
- Add a seal coat if the surface is raw wood.
- Choose tabletop or deep pour epoxy based on depth.
- Round up to the next kit size.